1466 PTO Rebuild


			• Public Gallery • Help

		• Join Now! • Log In • Feature Tour

Dan Allred | Home >

1466 PTO Rebuild

Putting the pto back together

Date(s): February 13, 2008. Album by Dan Allred. 1 - 45 of 45 Total. 7184 Visits.

Sign the Guestbook. Displaying 3 of 3 entries.

Even better than the manual THANKS !!!!!
- Lindsey Hill, Sat, 1 Sep 2018 1:46PM

Outstanding. Thank you for taking the time to document the procedure and posting the pictures.
- Richard D Salyer, Thu, 29 Dec 2016 11:45AM

tHANKS YOU FOR TAKING THE TIME TO RECORD THIS
- kYLE WALTON, Sat, 2 Mar 2013 8:01PM

1 DSCF7868 Fully assembled PTO	2 DSCF7784 Make sure the brass washer is in place	3 DSCF7785 Install the 540 seal from the inside	4 DSCF7788 Install the 1000 seal from the outside
5 DSCF7793 Install the 540 shaft and snap ring	6 DSCF7794 Install the 540 gear	7 DSCF7797 Isntall the snap ring to hold the gear	8 DSCF7801 Install a new O-ring on 1000 shaft
9 DSCF7802 Install the 1000 shaft and snap ring	10 DSCF7804 Install the idler gear and pin	11 DSCF7808 Check the little pin in the spool and make sure its not loose or worn	12 DSCF7815 Spool and related parts
13 DSCF7812 Install new stem seal in stem gland	14 DSCF7820 Install new boot on assembled spool	15 DSCF7821 Install new gasket on hosuing. Make sure you get the right one	16 DSCF7824 Install new brake pistons after the new O-rings are installed
17 DSCF7825 Install brake springs on pistons	18 DSCF7826 Install thrust washer and make sure tab is in slot. I put a little grease on the back of it to hold it.	19 DSCF7828 Set housing on lower half and make sure everything stays in place	20 DSCF7831 Install bolts and draw halves together evenly
21 DSCF7832 Make sure machined flat on idler pin is lined up with pump groove	22 DSCF7834 Check teflon rigns for wear and damage. If they are good they are reusuable	23 DSCF7836 Install clutch basket and compress with tool to get snap ring groove to line up	24 DSCF7838 Install snap ring
25 DSCF7839 Install new O-ring in center of clutch piston	26 DSCF7840 Install new lip seal on outside of piston. Make sure lip points toward the oil side	27 DSCF7841 Install piston using a downward twisting motion to avoid cutting the lip seal. Some units will have another snap ring to install on the shaft after the piston	28 DSCF7844 I always like to braze the clamp to the tube before I take it off to install a new seal. This prevents knocking it loose during installation
29 DSCF7846 Measure the distance of the seal before removing. The book also has a spec on this	30 DSCF7847 Check suction tube screen and clean as needed	31 DSCF7848 Install clutch disks starting with 2 metal ones first	32 DSCF7849 Then install a fiber disk
33 DSCF7850 Alternate fiber, metal, fiber and so on untill all 7 fibers and 9 metals are installed and ending with a metal disk	34 DSCF7851 Install large spacer	35 DSCF7852 Install snap ring	36 DSCF7853 Check for side movement of clutches
37 DSCF7855 Install spring and spring tool and compress spring to get snap ring on	38 DSCF7856 Make sure snap ring is seated in groove and inside the rabbited area of spring retainer	39 DSCF7857 Install a new pump base gasket and make sure oil hole is lined up	40 DSCF7858 Be sure idler flat is lined up again
41 DSCF7859 Check needle bearing inside pump hub	42 DSCF7865 Install pump and using a twisting downward force intill all disks are splined up and pump is setting on gasket. You can look inside the clutch stack to make sure the lowest disk turns when pump shaft is rotated	43 DSCF7867 Again, make sure idler flat is properly aligned	44 DSCF7870 Apply some grease to transmission and stick the mounting gasket in place
45 DSCF7871 After the PTO is in place tighten all the bolts

Select All.

Album Properties. Email Album. Send Invitation. Add to Website. Share URL