1
Dodge and Fargo truck 1954-58-66 floor mat
Finally a hign quality replacement floor mat to fit 1954-58 Dodge and Fargo trucks including Sweptside, Sweptline, Utiline, Cab and Chassis, Stake, Town Wagon, Town Panel and some Power Wagon models [does not fit WDX, PW, WM300 W300M or COE models] and will also fit the 1959-1960 Dodge trucks and the 1959-66 Town Wagon and Town Panel models with slight trimming. These replacement black rubber floor mats are new, 2007 production, they are made of 100% rubber and weight approx. 10 pounds ea.! They have holes cut for the steering collumn, gas pedal and gas pedal rod. They have knock out's for high beam switch and heater with no holes cut for a floor shifter or pedals through the floor. This mat is moulded to fit both floor pans and trans. cover like a glove. I have installed this mat in 2 of my trucks, one early and one late, and they fit great! Guaranteed!
Mat is $114.00 + $15.00 for shipping and insur. Boxed well for safe shipping.
| 
2
1954-58-66 floor mat
This mat is nice and flexable even at 0.010" thick. It measures approx. " wide at the widest point. Total height is " long so it runs from the ridge in front of the seat all the way to approx. 12" up the firewall and has a perferated "knock out" area to clear the heater.
|
3
floor mat installed 1964 panel
This is the mat I installed in my 1964 W100 Town Panel. It took only minor trimming around the steering collum and on each side by the door steps. It's even moulded around the transfer case levers! Really fits nice and looks good.
| 
4
Power wagon name plates 002
These are for all four wheel drive Dodge trucks 1958-68 and are used on some later civ. Power Wagon's. These are as cast and are $70.00 Pr. + shipping.
|
5
repro Power Wagon nameplates 001
These are for Dodge Std. cab four wheel drive trucks 1958-68 W100, W200, W300 and some W500. These are as cast and are $70.00 Pr.+ shipping
| 
6
repro Town wagon, Town Panel and Power Wagon nameplate
This is for the rear of Town Wagon's and Town Panels, and mount just under the rear passenger door. These were also used on the later Civ. Power Wagon's on the radiator shroud. This is as cast and is $35.00 + shipping
|
7
repro Town Wagon and Town Panel nameplates 004
These are for 1955-60 Town Wagon's and Town Panel's but will also fit on the later 1961-66 trucks. These are as cast and are $70.00 Pr. + shipping.
| 
8
Rebuilt door latches for 1957-66,1961-71 all Dodge trucks
I have been rebuilding door latches for a few years now. I have door latches for most 1957-60 Dodge trucks and 1957-66 Town Wagons and Town Panels. I also have the 1961-67 Dodge truck latches. Rebuilt latches are available in right or left and are $135.00 EA. with rebuildable core. I may be able to rebuild other latches[car's] of this era if I have the parts. I have a lot of NOS mopar latches on hand for car's and trucks and am also interested in purchasing cores.
|
9
Denver lock out wrench
This is an exact reproduction of the wrench supplied with the Denver brand locking hubs made in the late 50's and early 60's. These are $25.00 EA. + shipping.
| 
10
Orignal wiper motor for WC trucks and Power Wagon's
I now have 6V and 12V wiper kits available to fit W-series trucks, Power Wagons and closed cab WW2 military Dodge trucks. These are the same electric wipers Dodge installed as an option so they fit perfectly. They are strong, single speed motors, built in the USA and will last a lifetime.
Each kit includes 1 ea. NOS or re-built wiper motor with correct sweep and lenth of mounting stud, 1 set wiper motor mounting hardware, 1 set wiper arm adaptors, 1 ea. 3-way adjustable stainless wiper arm, 1 ea. NOS wiper blade holder and blade, 1 ea. wiper switch with mounting bezel & knob, and complete operating and installation instructions. The kits are fully guaranteed and are $225.00 ea.+ $12.00 for shipping & insurance.
If you have these wipers in your truck I may be able to rebuild your wiper motors as I have many parts. I am also looking to buy cores and parts. Inquire for more information. John : cjlapham@yahoo.com
|
11
CLUTCH AND BRAKE MASTER SLEEVED WITH STAINLESS STEEL
These are available as a brake master as used on 1959-66 light duty trucks or as a clutch master as used on 1959-66 trucks. These have been baked, blasted, sleeved with stainless steel and honed to size. Then they are cleaned and sprayed with 3 to 4 coats of clear polyurathane and come complete with O.E. manufacturer rebuild kit and all necessary hardware. These will outlast any stock cylinder and look good doing it! These are $80.00 + $10.00 shipping and insurance
| 
12
CLUTCH SLAVE CYLINDERS SLEEVED WITH STAINLESS STEEL
This clutch slave cylinder as used on 1959-68 Dodge light duty trucks. These orignal cylinders have been bead blasted, baked, sleeved with stainless steel and honed to size, sprayed with 3 or 4 coats of clear polyurathane paint. The cylinders are then then cleaned and rebuilt using O.E. parts and a new bleeder screw added. This will stop your clutch problems due to rust and contamanation for good! $80.00 + $10.00 for shipping and insurance.
|
13
BRAKE MASTER CYLINDER SLEEVED WITH STAINLESS STEEL
This sleeved master will fit 1958 and earler trucks and some later civ. power wagon's. These cylinders have been baked, blasted,sleeved with stainless steel and honed to size. Then they are cleaned and sprayed with 3 to 4 coats of polyurathane clear. They are available in various diameters to match your orignal cylinder and come with an O.E. rebuild kit and all nessary hardware. These are perfect for all trucks esp. those that get only ocasional use and are compatable with all types of brake fluid. $100.00 + $10.00 for shipping and insurance.
| 
14
Dodge Fargo truck 1955-60 mirror arm with mounting bracket
This is a faithful reproduction of the factory installed out side mirror arm for the second series 1955-1960 trucks. This arm and brackets are made of the same gauge steel as orignal and fits the two orignal holes in the door. These will fit right or left side and are $40.00 including shipping and insurance.
|
15
Dodge Fargo truck 1955-60 mirror arm
This is a faithful reproduction of the factory installed out side mirror arm for the second series 1955-1960 trucks. This arm is made of the same gauge steel as orignal and fits the the brackets mounter to the two orignal holes in the door. These will fit right or left side and are $30.00 including shipping and insurance
| 
16
|
